Domain 3IP ConnectivityCORE

First Hop Redundancy Protocols

First Hop Redundancy Protocols (FHRP) including HSRP, VRRP, and GLBP for providing default gateway redundancy and high availability in enterprise networks.

Domain: Domain 3: IP Connectivity•Updated: 2026-08-26
#FHRP#HSRP#VRRP#GLBP#Gateway Redundancy#High Availability

First Hop Redundancy Protocols (FHRPs)

Purpose and Basic Operation

  • Concept: First Hop Redundancy Protocols (FHRPs) protect the default gateway on a subnetwork by allowing two or more routers to provide backup for that address. If the active router fails, a backup router takes over the gateway address, usually within seconds.
  • Details:
    • Virtual IP (VIP): Routers share a single VIP. End hosts are configured to use this VIP as their default gateway instead of a physical router interface IP.
    • Virtual MAC (VMAC): The active router replies to ARP requests for the VIP using a generated VMAC. Each FHRP uses a specific, standardized VMAC format.
    • Hello Messages: Routers negotiate roles by sending multicast Hello messages to each other.
    • Gratuitous ARP (GARP): When a standby router takes over as active, it sends broadcast GARP messages. This forces switches to update their MAC address tables with the new port associated with the VMAC.
graph TD
    A[Host sends traffic to VIP] --> B{Host knows VMAC?}
    B -- No --> C[Host broadcasts ARP Request for VIP]
    C --> D[Active Router replies with VMAC]
    B -- Yes --> E[Host sends frame to VMAC]
    E --> F[Active Router forwards packet]
    F --> G{Active Router Fails?}
    G -- Yes --> H[Standby stops receiving Hellos]
    H --> I[Standby transitions to Active]
    I --> J[New Active sends Gratuitous ARP]
    J --> K[Switches update MAC tables]

Things to note:

  • Preemption: By default, FHRPs are non-preemptive (similar to OSPF DR/BDR). If the original active router fails and recovers, it will not automatically take back the active role. You must explicitly configure preemption to allow a router with a higher priority to reclaim the active state.
  • Election Rules: The router with the highest priority becomes Active. If priorities tie, the router with the highest IP address on the interface wins.

FHRP Comparison

Feature HSRP (Hot Standby Router Protocol) VRRP (Virtual Router Redundancy Protocol) GLBP (Gateway Load Balancing Protocol)
Vendor Cisco Proprietary Open Standard Cisco Proprietary
Roles Active, Standby Master, Backup AVG (Active Virtual Gateway), AVF (Active Virtual Forwarder)
IPv4 Multicast v1: 224.0.0.2
v2: 224.0.0.102
224.0.0.18 224.0.0.102
Virtual MAC Format v1: 0000.0c07.acXX
v2: 0000.0c9f.fXXX
0000.5e00.01XX 0007.b400.XXYY (XX=Group, YY=AVF)
Load Balancing Across multiple subnets/VLANs only Across multiple subnets/VLANs only Within a single subnet (up to 4 routers)

Things to note:

  • HSRP vs VRRP: Functionally nearly identical, but VRRP is an open standard and uses different terminology (Master/Backup instead of Active/Standby).
  • GLBP Load Balancing: Unlike HSRP/VRRP (which only allow one active forwarder per subnet), GLBP elects one AVG which assigns up to four AVFs. Each AVF acts as the default gateway for a portion of the hosts, achieving true active-active load balancing within a single subnet.

HSRP (Hot Standby Router Protocol) Details

  • Versions:
    • Version 1: Default. IPv4 only. Multicast 224.0.0.2. Supports groups 0–255.
    • Version 2: Adds IPv6 support. Multicast 224.0.0.102. Supports groups 0–4095.
  • Virtual MAC Examples:
    • HSRPv1 Group 1 (Hex 01): 0000.0c07.ac01
    • HSRPv2 Group 1 (Hex 001): 0000.0c9f.f001
  • Load Balancing Strategy: Configure multiple HSRP groups across different VLANs. Make Router 1 Active for VLAN 10 / Standby for VLAN 20, and Router 2 Standby for VLAN 10 / Active for VLAN 20.

VRRP (Virtual Router Redundancy Protocol) Details

  • Virtual MAC Example:
    • VRRP Group 200 (Decimal 200 = Hex C8): 0000.5e00.01c8
  • Load Balancing Strategy: Identical to HSRP. Configure different Master routers for different subnets/VLANs.

GLBP (Gateway Load Balancing Protocol) Details

  • Virtual MAC Example:
    • GLBP Group 1, AVF 1: 0007.b400.0101
  • Operation: The AVG responds to ARP requests for the VIP with different VMACs (round-robin by default) belonging to the various AVFs. This distributes host traffic across multiple physical routers.

HSRP Configuration & Verification

HSRP is configured directly on the Layer 3 interface connected to the subnet it is protecting.

! Enable HSRP Version 2 (Optional, but recommended for IPv6 and more groups)
Router(config-if)# standby version 2

! Configure the Virtual IP (VIP) for Group 1
Router(config-if)# standby 1 ip 172.16.0.254

! Set Priority (Range 0-255, Default is 100)
! Higher priority wins the Active election
Router(config-if)# standby 1 priority 200

! Enable Preemption so this router reclaims Active role if it recovers
Router(config-if)# standby 1 preempt

Verification Command:

Router# show standby

Output Breakdown:

  • Group & Version: Shows the HSRP group number and version (1 or 2).
  • State: Active or Standby.
  • Virtual IP: The configured VIP.
  • Virtual MAC: The generated VMAC for the group.
  • Timers: Hello and hold times (default is 3s hello, 10s hold).
  • Preemption: Shows if enabled or disabled.
  • Active/Standby IPs: Shows the physical IP of the local and peer routers.
  • Priority: Displays the configured priority value and the peer’s priority.

Things to note:

  • HSRPv1 and HSRPv2 are not compatible. Both routers in the same group must use the same version.
  • You only need to configure standby [group] preempt on the router you want to become Active. The standby router does not need preemption enabled to be preempted.

Summary of IOS Commands

! Interface Configuration Mode Commands
standby version 2                 ! Changes HSRP from v1 to v2
standby [group] ip [vip]          ! Sets the Virtual IP for the FHRP group
standby [group] priority [0-255]  ! Sets router priority for Active election (Default: 100)
standby [group] preempt           ! Allows router to reclaim Active role if it has highest priority

! Verification Commands
show standby                      ! Displays HSRP state, VIP, VMAC, priorities, and timers
show standby brief                ! Displays a summarized table of all HSRP groups on the router