Domain 1Network FundamentalsCORE

IPv6 Addressing and Operations

IPv6 address structure, types (unicast, multicast, anycast), SLAAC, EUI-64 interface IDs, and Neighbor Discovery Protocol (NDP).

Domain: Domain 1: Network Fundamentals•Updated: 2026-08-26
#IPv6#Address Types#SLAAC#EUI-64#NDP

IPv6 Fundamentals, Addressing, and Routing

Introduction & Numbering Systems

  • Concept: IPv6 was developed to solve IPv4 address exhaustion. IPv4 provides ~4.3 billion addresses (32-bit), while IPv6 provides 2^128 addresses (128-bit).
  • Details:
    • IANA (Internet Assigned Numbers Authority) distributes addresses to RIRs (Regional Internet Registries: AFRINIC, APNIC, ARIN, LACNIC, RIPE NCC). Most RIRs have exhausted IPv4 pools.
    • IPv5: Internet Stream Protocol (experimental, used version field 5, never public).
    • Numbering Systems:
      • Binary (Base 2): Prefix 0b. Digits: 0, 1.
      • Decimal (Base 10): Prefix 0d. Digits: 0-9.
      • Hexadecimal (Base 16): Prefix 0x. Digits: 0-9, A-F. 1 hex digit = 4 bits.

Things to note: Memorize hex conversions for 10-15 (A=10, B=11, C=12, D=13, E=14, F=15). Every additional bit doubles the address space.

IPv6 Addressing Basics

  • Concept: IPv6 addresses are 128 bits long, written as 32 hexadecimal characters divided into 8 groups of 4 (quartets) separated by colons.
  • Details:
    • Prefix Length: Uses slash notation (e.g., /64) directly in the CLI. No dotted-decimal subnet masks.
    • RFC 5952 (Standard Representation):
      1. Leading zeros in a quartet MUST be removed.
      2. Double colon (::) MUST be used for the longest consecutive string of all-0 quartets.
      3. If there is a tie for the longest string, use :: on the left-most string.
      4. Hexadecimal letters (A-F) MUST be lowercase.
    • Shortening Rules:
      • Remove leading zeros (e.g., 01 -> 1).
      • Replace consecutive all-0 quartets with ::. Can only be done ONCE per address.
    • Expanding Rules:
      • Add leading zeros to ensure every quartet has 4 characters.
      • Replace :: with enough 0000 quartets to equal exactly 8 total quartets.

Things to note: You cannot use :: twice. If you have two sets of consecutive zeros, use :: for the longest set (or left-most if tied), and just drop leading zeros for the other set.

Finding the IPv6 Network Prefix

  • Concept: Similar to IPv4, change all host bits to 0 to find the network prefix.
  • Details:
    • If prefix length is a multiple of 4 (e.g., /64, /56): Simply change all hex characters after the prefix boundary to 0.
    • If prefix length is NOT a multiple of 4 (e.g., /93): You must convert the boundary hex digit to binary, zero out the host bits, and convert back to hex.
      • Example: /93 ends in the middle of the 24th hex digit. Convert that hex digit to 4 binary bits, keep the first bit (network), change the remaining 3 bits to 0, and convert back to hex.

IPv6 Address Types

Address Type Prefix / Range Scope / Routing Description
Global Unicast (GUA) 2000::/3 (Originally), now all unassigned Routable over Internet Public addresses. Requires registration.
Unique Local (ULA) FC00::/7 (Usually FD) Routable internally, dropped by ISP Private addresses. No registration needed.
Link-Local FE80::/10 (Usually FE80) Non-routable (Local subnet only) Auto-generated. Used for routing protocols/NDP.
Multicast FF00::/8 Varies by scope One-to-many. Replaces IPv4 Broadcast.
Anycast Any Unicast range Routable One-to-one-of-many. Nearest router responds.
Unspecified ::/0 N/A All zeros. Used when device doesn’t know its IP.
Loopback ::1/128 Local device only Tests protocol stack. Equivalent to 127.0.0.1.

Global Unicast Address (GUA) Structure

  • Global Routing Prefix: Typically /48 assigned by ISP.
  • Subnet Identifier: Typically 16 bits (allows 65,536 subnets).
  • Interface Identifier: 64 bits (Host portion).
  • Total Prefix: Usually /64.

Unique Local Address (ULA) Structure

  • FD: Indicates ULA.
  • Global ID: 40 bits. Must be randomly generated to prevent overlaps if companies merge.
  • Subnet ID: 16 bits.
  • Interface ID: 64 bits.

Multicast Scopes

Scope Prefix Description
Interface-Local FF01:: Stays within the local device (node-local).
Link-Local FF02:: Stays within the local subnet. Not routed.
Site-Local FF05:: Limited to a single physical site/WAN boundary.
Organization-Local FF08:: Wider scope, across multiple sites in an org.
Global FF0E:: Routable across the public Internet.

Important Multicast Addresses:

  • FF02::1: All Nodes (All Hosts) - Functions like a broadcast.
  • FF02::2: All Routers.
  • FF02::5: All OSPF Routers (IPv4: 224.0.0.5).
  • FF02::A: All EIGRP Routers (IPv4: 224.0.0.10).

EUI-64 & SLAAC

  • Concept: Methods to automatically generate the 64-bit Interface ID (host portion) of an IPv6 address.
  • EUI-64 (Extended Unique Identifier): Converts a 48-bit MAC address into a 64-bit Interface ID.
    1. Split the MAC address in half.
    2. Insert FFFE in the middle.
    3. Invert the 7th bit (the Universal/Local or U/L bit). If it’s 0, make it 1. If 1, make it 0.
  • SLAAC (Stateless Address Autoconfiguration): Hosts automatically learn the IPv6 prefix from the local router and generate their own Interface ID (via EUI-64 or random generation) without a server.

Things to note: The 7th bit inversion in EUI-64 reverses the meaning of the U/L bit. In MAC addresses, 0 = Universally Administered (UAA). In EUI-64, 0 means it was derived from a Locally Administered Address (LAA).

Neighbor Discovery Protocol (NDP) & ICMPv6

  • Concept: NDP replaces ARP in IPv6. It uses ICMPv6 messages and multicast to discover neighbors, routers, and detect duplicate addresses.
  • Details:
    • Solicited-Node Multicast Address: Calculated from a unicast address. Format: FF02::1:FF + last 6 hex digits of the unicast address. Used to make NDP highly efficient (multicast instead of broadcast).
    • DAD (Duplicate Address Detection): When an interface initializes or gets an IP, it sends a Neighbor Solicitation to its own solicited-node multicast address. If no reply is received, the IP is unique.
ICMPv6 Type Message Name Function Destination
133 Router Solicitation (RS) Host asks for routers on the link. FF02::2 (All Routers)
134 Router Advertisement (RA) Router announces presence, prefix, etc. FF02::1 (All Nodes)
135 Neighbor Solicitation (NS) Asks for a neighbor’s MAC address (Replaces ARP Request). Target’s Solicited-Node Multicast
136 Neighbor Advertisement (NA) Replies with MAC address (Replaces ARP Reply). Requester’s Unicast IP
sequenceDiagram
    participant R1
    participant R2
    R1->>R2: NS (ICMPv6 135) to R2's Solicited-Node Multicast
    Note over R1,R2: "What is your MAC address?"
    R2->>R1: NA (ICMPv6 136) to R1's Unicast IP
    Note over R1,R2: "My MAC is XX:XX:XX..."

IPv6 Header

  • Concept: The IPv6 header is simplified and has a fixed size of 40 bytes (unlike IPv4’s variable 20-60 bytes), improving router processing efficiency.
  • Fields:
    • Version (4 bits): Always 6 (binary 0110).
    • Traffic Class (8 bits): Used for QoS (Quality of Service).
    • Flow Label (20 bits): Identifies specific traffic flows (e.g., server-client interaction).
    • Payload Length (16 bits): Length of the Layer 4 segment in bytes.
    • Next Header (8 bits): Indicates the encapsulated protocol (TCP, UDP, etc.). Equivalent to IPv4’s Protocol field.
    • Hop Limit (8 bits): Decremented by 1 at each router. Packet dropped at 0. Equivalent to IPv4’s TTL.
    • Source Address (128 bits): Sender’s IPv6 address.
    • Destination Address (128 bits): Receiver’s IPv6 address.

IPv6 Static Routing

  • Concept: IPv6 routing uses a separate routing table from IPv4. IPv6 routing is disabled by default and must be enabled globally.
  • Details:
    • Route Types:
      • Recursive: Specifies only the next-hop IP. Requires two lookups (destination -> next-hop -> exit interface).
      • Directly Attached: Specifies only the exit interface. WARNING: Does NOT work on Ethernet interfaces in IPv6! (Works on Serial).
      • Fully Specified: Specifies both exit interface and next-hop IP. Required when using a Link-Local address as the next hop.
    • Floating Static Route: A backup route with a manually increased Administrative Distance (AD). Must be higher than the primary routing protocol’s AD (e.g., >110 for OSPF, >90 for EIGRP).
    • Route Codes in show ipv6 route:
      • Connected network routes are added automatically.
      • Local host routes (/128) are added for configured interface IPs.
      • Link-local addresses do not appear in the routing table.
graph TD
    A[Packet Arrives] --> B{Lookup Destination in IPv6 Routing Table}
    B --> C[Most Specific Match Wins]
    C --> D[Forward out Exit Interface to Next-Hop]

Things to note: If your IPv6 config looks perfect but traffic isn’t routing, you almost certainly forgot ipv6 unicast-routing. Also, remember that directly attached static routes fail silently on GigabitEthernet interfaces in IPv6.


Command Reference Summary

Global Configuration

Router(config)# ipv6 unicast-routing
! Enables IPv6 routing globally (DISABLED BY DEFAULT)

Interface Configuration

Router(config-if)# ipv6 address <ipv6-address>/<prefix-length>
! Configures a static IPv6 address (e.g., 2001:db8:0:1::1/64)

Router(config-if)# ipv6 address <ipv6-prefix>/<prefix-length> eui-64
! Generates Interface ID automatically from the interface's MAC address

Router(config-if)# ipv6 address autoconfig
! Enables SLAAC (learns prefix from Router Advertisements)

Router(config-if)# ipv6 enable
! Enables IPv6 on the interface and auto-generates a Link-Local address only

Router(config-if)# ipv6 address <ipv6-address>/<prefix-length> anycast
! Configures an Anycast address (usually with /128)

Router(config-if)# no shutdown
! Activates the interface

Static Routing

Router(config)# ipv6 route <prefix>/<prefix-length> <next-hop-ip>
! Recursive static route

Router(config)# ipv6 route <prefix>/<prefix-length> <exit-interface> <next-hop-ip>
! Fully specified static route (REQUIRED for link-local next-hops)

Router(config)# ipv6 route <prefix>/<prefix-length> <next-hop-ip> <AD>
! Floating static route (e.g., AD 120 for OSPF backup)

Verification & Troubleshooting

Router# show ipv6 interface brief
! Displays IPv6 addresses (including auto-generated Link-Local) and status

Router# show ipv6 interface <interface>
! Shows detailed IPv6 info, including joined multicast groups

Router# show ipv6 route
! Displays the IPv6 routing table

Router# show ipv6 neighbor
! Displays the NDP neighbor table (equivalent to show ip arp)

Router# ping ipv6 <destination-ip>
! Tests IPv6 connectivity