Domain 2Network AccessCORE

Wireless Configuration and Troubleshooting

Configuring and troubleshooting basic wireless networks, including SSID setup, CAPWAP tunnels, and WLC GUI management.

Domain: Domain 2: Network Access•Updated: 2026-08-26
#WLAN Config#SSID#CAPWAP#WLC GUI#Wireless Troubleshooting

Wireless LAN Configuration (CCNA 200-301)

Network Topology & Switch Configuration

In a Split-MAC deployment, the Wireless LAN Controller (WLC) handles management and control planes, while Access Points (APs) handle the real-time data forwarding.

  • Power over Ethernet (PoE): APs receive both data and power through a single Ethernet cable.
  • Switch Ports to APs: Configured as Access Ports in the Management VLAN. The APs encapsulate wireless traffic into CAPWAP (Control and Provisioning of Wireless Access Points) tunnels to send to the WLC.
  • Switch Ports to WLC: Configured as a Trunk Port bundled in a LAG (Link Aggregation Group).
  • LAG Constraint: WLCs only support Static LAG. They do not support negotiation protocols like PAgP or LACP.

VLAN & IP Addressing Scheme

VLAN ID Name Subnet Switch SVI (Default GW) WLC IP Address Purpose
10 Management 192.168.1.0/24 192.168.1.1 192.168.1.100 Device management, AP-to-WLC CAPWAP
100 Internal 10.0.0.0/24 10.0.0.1 10.0.0.100 Mapped to Internal WLAN (SSID)
200 Guest 10.1.0.0/24 10.1.0.1 10.1.0.100 Mapped to Guest WLAN (SSID)

Switch Configuration Commands

! Create VLANs
Switch(config)# vlan 10
Switch(config-vlan)# name Management
Switch(config)# vlan 100
Switch(config-vlan)# name Internal
Switch(config)# vlan 200
Switch(config-vlan)# name Guest

! Configure Access Ports for APs and Management PC
Switch(config)# interface range fastethernet 0/6 - 8
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 10
Switch(config-if)# spanning-tree portfast

! Configure Static LAG (EtherChannel) to WLC
Switch(config)# interface range fastethernet 0/1 - 2
Switch(config-if)# switchport mode trunk
Switch(config-if)# channel-group 1 mode on
Switch(config-if)# no shutdown

! Configure Port-Channel Interface
Switch(config)# interface port-channel 1
Switch(config-if)# switchport trunk allowed vlan 10,100,200

! Configure SVIs for Default Gateways
Switch(config)# interface vlan 10
Switch(config-if)# ip address 192.168.1.1 255.255.255.0
Switch(config)# interface vlan 100
Switch(config-if)# ip address 10.0.0.1 255.255.255.0
Switch(config)# interface vlan 200
Switch(config-if)# ip address 10.1.0.1 255.255.255.0

! Configure DHCP Pools
Switch(config)# ip dhcp pool VLAN10_POOL
Switch(dhcp-config)# network 192.168.1.0 255.255.255.0
Switch(dhcp-config)# default-router 192.168.1.1
Switch(dhcp-config)# option 43 ip 192.168.1.100
! Note: Option 43 tells APs the WLC's IP if they are in a different subnet.

Switch(config)# ip dhcp pool VLAN100_POOL
Switch(dhcp-config)# network 10.0.0.0 255.255.255.0
Switch(dhcp-config)# default-router 10.0.0.1

Switch(config)# ip dhcp pool VLAN200_POOL
Switch(dhcp-config)# network 10.1.0.0 255.255.255.0
Switch(dhcp-config)# default-router 10.1.0.1

! Enable NTP Server on Switch
Switch(config)# ntp master

Things to note:

  • DHCP Option 43 is critical when APs and WLCs are in different subnets. If they are in the same subnet, APs use Layer 2 broadcasts for CAPWAP discovery.
  • APs connect to Access ports, not Trunk ports. The CAPWAP tunnel handles the VLAN tagging internally.

Split-MAC Traffic Flow

graph TD
    Client((Wireless Client)) -- Wi-Fi SSID --> AP[Access Point]
    AP -- CAPWAP Tunnel --> WLC[Wireless LAN Controller]
    WLC -- Dynamic Interface VLAN 100 --> SW[Switch Trunk/Port-Channel]
    SW -- Routed via SVI --> GW[Default Gateway 10.0.0.1]

WLC Physical Ports vs. Logical Interfaces

A common misconception is using “port” and “interface” interchangeably. On a WLC, they mean distinctly different things.

Feature WLC Ports (Physical) WLC Interfaces (Logical)
Definition Physical hardware connectors where cables plug in. Virtual/Logical interfaces inside the WLC OS (similar to SVIs).
Service Port Dedicated out-of-band management port (supports only 1 VLAN). Bound to the physical service port for out-of-band management.
Distribution System Standard network ports for data traffic. Can form a LAG. N/A (Physical ports mapped to logical interfaces).
Console Port RJ45 or USB port for direct CLI access. N/A
Redundancy Port Connects to another WLC to form a High Availability (HA) pair. Redundancy Mgmt Interface: Used to manage the standby WLC in an HA pair.
N/A N/A Management Interface: Used for in-band management (SSH, HTTPS, RADIUS, CAPWAP endpoints).
N/A N/A Virtual Interface: Used for client communications (DHCP relay, Web Auth). Must be an unused IP.
N/A N/A Dynamic Interfaces: Used to map a specific WLAN (SSID) to a specific wired VLAN.

WLC Initial Setup (CLI Wizard)

When a WLC boots for the first time, it launches a CLI configuration wizard.

  • Autoinstall: Skipped (used to download config from TFTP).
  • LAG Setup: Must select yes to enable Link Aggregation if connecting via a Port-Channel.
  • Management Interface IP: Assigns the in-band management IP (e.g., 192.168.1.100).
  • Virtual Gateway IP: Used for client communications (DHCP relay).
  • Regulatory Domain (Country Code): CRITICAL. The WLC’s country code must match the AP’s hardware regulatory domain (e.g., -E for Europe, -A for US/Canada). If they mismatch, the AP will fail to join the WLC.
  • Auto-RF: Allows WLC to automatically assign channels and transmit power.

Configuring WLC Interfaces & WLANs (GUI)

Once the CLI setup is complete, access the GUI via HTTPS using the Management IP.

1. Create Dynamic Interfaces

Dynamic interfaces map a WLAN to a specific VLAN on the wired network.

  • Navigate to Controller > Interfaces > New.
  • Internal Interface: Map to VLAN 100, assign IP 10.0.0.100/24.
  • Guest Interface: Map to VLAN 200, assign IP 10.1.0.100/24.

2. Configure WLANs (SSIDs)

Navigate to WLANs > Create New.

  • Profile Name: Internal identifier in the WLC.
  • SSID: The actual broadcasted wireless network name.
  • ID: Unique numeric identifier (e.g., 1 for Internal, 2 for Guest).
  • Interface Mapping: Change from Management Interface to the correct Dynamic Interface (e.g., Internal).

3. Security Policies

Navigate to the Security tab of the WLAN.

  • Layer 2 Security: Select WPA + WPA2.
  • Authentication Key Management: Change from 802.1X to PSK (Pre-Shared Key).
    • ASCII format: Requires a minimum of 8 characters.
    • HEX format: Hexadecimal password.
  • Layer 3 Security: Optional. Includes Web Authentication (requires username/password via captive portal) or Web Passthrough (requires clicking “Accept” on a splash page). Common for Guest networks.

WLC QoS & Management Features

WLAN QoS Levels

Configured in the QoS tab of the WLAN settings. Determines the priority of wireless traffic.

QoS Level Priority Recommended Usage
Platinum Highest Voice (e.g., Wi-Fi IP phones)
Gold High Video streaming
Silver Medium (Default) Best effort data (Standard web browsing)
Bronze Lowest Background traffic (e.g., backups)

Management & CPU ACLs

  • Management via Wireless: Disabled by default. If enabled, wireless clients can manage the WLC GUI/CLI. Best practice is to leave it disabled.
  • CPU Access Control Lists (ACLs):
    • Used to filter and restrict management traffic destined directly for the WLC’s CPU (e.g., SSH, HTTPS, SNMP).
    • Does NOT affect transit traffic passing through the WLC from wireless clients to the wired network.
    • Applied under Security > Access Control Lists > CPU Access Control Lists.

Summary of Commands

! --- SWITCH CONFIGURATION ---
! VLAN Creation
Switch(config)# vlan [10-200]
Switch(config-vlan)# name [Name]

! AP Access Ports
Switch(config)# interface range fa0/7 - 8
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 10

! Static LAG to WLC (No PAgP/LACP!)
Switch(config)# interface range fa0/1 - 2
Switch(config-if)# switchport mode trunk
Switch(config-if)# channel-group 1 mode on
Switch(config)# interface port-channel 1
Switch(config-if)# switchport trunk allowed vlan 10,100,200

! DHCP Option 43 for AP Discovery
Switch(config)# ip dhcp pool VLAN10_POOL
Switch(dhcp-config)# option 43 ip [WLC_Management_IP]

! --- WLC GUI CONFIGURATION PATHS ---
! Create Dynamic Interface: Controller > Interfaces > New
! Create WLAN: WLANs > Create New
! Change Security: WLANs > [WLAN_ID] > Security > Layer 2 > WPA2 + PSK
! Change QoS: WLANs > [WLAN_ID] > QoS > [Platinum/Gold/Silver/Bronze]
! Apply CPU ACL: Security > Access Control Lists > CPU Access Control Lists