RHCSA Commands: Extras and Practice
Boot Troubleshooting & Recovery
| Command | Description | Example |
|---|---|---|
mount -o remount,rw / |
Remounts the root filesystem as read/write during emergency/rescue modes | mount -o remount,rw / |
passwd |
Changes the root password in single-user/rescue modes | passwd |
touch /.autorelabel |
Forces SELinux to relabel all files on the next reboot (critical after password reset via init=/bin/bash) |
touch /.autorelabel |
exec /usr/lib/systemd/systemd |
Replaces the current shell (PID 1) with systemd to resume normal boot after init=/bin/bash |
exec /usr/lib/systemd/systemd |
chroot /mnt/sysimage |
Changes the root directory to the mounted rescue system to repair it | chroot /mnt/sysimage |
grub2-install |
Reinstalls the GRUB 2 bootloader to the specified disk | grub2-install /dev/sda or grub2-install /dev/vda |
dracut --force |
Rebuilds the initramfs image; --force overwrites the existing one |
dracut --force |
journalctl -xb |
Views boot logs to diagnose why a filesystem or service failed to mount/start | journalctl -xb |
systemctl list-units |
Lists all currently loaded systemd unit files (useful in rescue/emergency targets) | systemctl list-units |
systemctl show-environment |
Shows current shell environment variables | systemctl show-environment |
systemctl reboot |
Reboots the machine from rescue mode | systemctl reboot |
reboot |
Restarts the system (standard mode) | reboot |
systemctl isolate multi-user.target |
Switches to multi-user target manually | systemctl isolate multi-user.target |
systemctl set-default |
Sets the default boot target | systemctl set-default multi-user.target |
grub2-mkconfig |
Regenerates the GRUB configuration file | grub2-mkconfig -o /boot/grub2/grub.cfg |
GRUB Boot Arguments (not commands but critical for troubleshooting)
| Argument | Description | Example |
|---|---|---|
init=/bin/bash |
Boots directly into a bash shell as PID 1 (no password required) | Append to linux line at GRUB |
init=/bin/sh |
Boots directly into a sh shell as PID 1 | Append to linux line at GRUB |
rd.break |
Stops boot in initramfs stage (requires root password) | Append to linux line at GRUB |
systemd.unit=emergency.target |
Enters minimal troubleshooting mode (requires root password) | Append to linux line at GRUB |
systemd.unit=rescue.target |
Starts more systemd units for a more complete rescue mode (requires root password) | Append to linux line at GRUB |
rhgb |
Red Hat Graphical Boot (hides boot messages) | Remove to see verbose boot |
quiet |
Suppresses boot messages | Remove to see verbose boot |
Containers / Podman
Image Management
| Command | Description | Example |
|---|---|---|
podman search |
Searches configured registries for images | podman search mysql |
podman search --no-trunc |
Searches without truncating output | podman search --no-trunc mysql |
podman search --limit <n> |
Limits search results to N entries | podman search --limit 5 nginx |
podman pull |
Downloads an image from a registry to local storage | podman pull registry.redhat.io/ubi9 |
podman images |
Lists locally stored container images | podman images |
podman inspect |
Displays detailed JSON metadata of a local image or container | podman inspect ubi9 |
podman rmi |
Removes an image from local storage | podman rmi ubi9 |
podman rmi -a |
Removes all locally stored images | podman rmi -a |
podman tag |
Adds a name/tag to an image | podman tag ubi9:latest myregistry/ubi9:v1 |
podman login |
Logs in to a container registry | podman login registry.redhat.io |
podman logout |
Logs out from a container registry | podman logout registry.redhat.io |
podman info |
Reveals system information, including defined registries | podman info |
podman build |
Builds a custom image from a Containerfile | podman build -t myimage:1.0 . |
Container Lifecycle
| Command | Description | Example |
|---|---|---|
podman run |
Launches a new container from an image | podman run -d --name web -p 8080:80 -v /data:/data:Z nginx |
podman run -d |
Runs a container in detached (background) mode | podman run -d --name web nginx |
podman run -it |
Runs a container interactively with a terminal | podman run -it ubi8 |
podman run --name |
Assigns a name to a container | podman run --name myapp ubi8 |
podman run --rm |
Auto-removes the container after it exits | podman run --rm ubi7 ls |
podman run -p |
Maps a host port to a container port | podman run -p 10000:80 nginx |
podman run -v |
Mounts a host directory into the container (bind mount) | podman run -v /host_data:/container_data:Z ubi8 |
podman run -e |
Passes or sets an environment variable | podman run -e SECRET=secret123 ubi8 |
podman ps |
Lists running containers | podman ps |
podman ps -a |
Lists all containers (including stopped/exited) | podman ps -a |
podman start |
Starts a stopped container | podman start web1 |
podman stop |
Gracefully stops a running container (SIGTERM, then SIGKILL) | podman stop web1 |
podman restart |
Restarts a container | podman restart web1 |
podman rm |
Removes a stopped container | podman rm web1 |
podman rm -a |
Removes all stopped containers | podman rm -a |
podman exec |
Executes a command inside a running container | podman exec -it web1 /bin/sh |
podman attach |
Attaches to a running container’s terminal | podman attach web1 |
podman logs |
Fetches the logs of a container | podman logs web1 |
podman port |
Shows port mappings for a container | podman port web1 |
Rootless Containers & Systemd Integration
| Command | Description | Example |
|---|---|---|
podman generate systemd |
Generates a systemd unit file for an existing container | podman generate systemd --name web1 --files --new |
podman unshare |
Runs a command inside the rootless user namespace (fixes UID mappings) | podman unshare chown 27:27 /data |
loginctl enable-linger |
Enables a user’s systemd services to run at boot without an active login session | loginctl enable-linger student |
systemctl --user enable --now |
Enables/starts a user-level (rootless) systemd service | systemctl --user enable --now container-web1.service |
systemctl daemon-reload |
Reloads systemd configuration after adding new unit files | systemctl daemon-reload |
systemctl enable --now |
Enables and starts a system-level service | systemctl enable --now container-root-container.service |
systemctl status |
Checks the status of a service | systemctl status container-web1.service |
systemctl restart |
Restarts a service | systemctl restart container-web1.service |
Skopeo
| Command | Description | Example |
|---|---|---|
skopeo inspect |
Inspects a remote image in a registry without downloading it | skopeo inspect docker://docker.io/nginx |
Container Configuration Files
| File/Directory | Description |
|---|---|
/etc/containers/registries.conf |
System-wide registry configuration (search, insecure, block lists) |
~/.config/containers/registries.conf |
Per-user registry configuration (overrides system-wide) |
~/.config/systemd/user/ |
Per-user systemd unit files for rootless containers |
/etc/systemd/system/ |
System-level systemd unit files for root containers |
Apache HTTP Server
| Command | Description | Example |
|---|---|---|
dnf install httpd |
Installs the Apache web server package | dnf install httpd |
dnf group install "Basic Web Server" |
Installs Apache and all related packages | dnf group install "Basic Web Server" |
dnf install httpd-manual |
Installs the Apache documentation | dnf install httpd-manual |
systemctl enable --now httpd |
Starts the Apache service and enables it to start on boot | systemctl enable --now httpd |
systemctl status httpd |
Checks the status of the Apache service | systemctl status httpd |
systemctl restart httpd |
Restarts the Apache service | systemctl restart httpd |
curl http://localhost |
Tests the web server from the command line | curl http://localhost |
dnf install curl |
Installs the curl utility for testing | dnf install curl |
grep -v '#' /etc/httpd/conf/httpd.conf |
Shows non-comment lines in the Apache config | grep -v '#' /etc/httpd/conf/httpd.conf |
setenforce 0 |
Temporarily sets SELinux to permissive mode | setenforce 0 |
mkdir -p |
Creates directories recursively (for virtual host document roots) | mkdir -p /www/docs/account.example.com |
Apache Configuration Files
| File/Directory | Description |
|---|---|
/etc/httpd/conf/httpd.conf |
Main Apache configuration file |
/etc/httpd/conf.d/ |
Drop-in configuration directory (virtual hosts go here) |
/etc/httpd/conf.modules.d/ |
Module-specific configuration files |
/var/www/html |
Default document root |
DocumentRoot |
Config parameter specifying where Apache serves documents from |
ServerRoot |
Config parameter defining where Apache looks for config files (default: /etc/httpd) |
<VirtualHost *:80> |
Virtual host directive for name-based virtual hosting on port 80 |
SELinux
| Command | Description | Example |
|---|---|---|
setenforce 0 |
Temporarily sets SELinux to permissive mode | setenforce 0 |
setenforce 1 |
Sets SELinux back to enforcing mode | setenforce 1 |
semanage port -a |
Adds a port to the SELinux policy database persistently | semanage port -a -t http_port_t -p tcp 8300 |
semanage boolean |
Modifies SELinux booleans persistently | semanage boolean -m --on nfs_export_all_rw |
chcon |
Changes SELinux context on files/directories | chcon -t shadow_t /usr/testfile1 |
semanage fcontext |
Sets persistent SELinux context rules | semanage fcontext -a -t shadow_t '/usr/testfile1' |
restorecon |
Restores SELinux contexts based on policy rules | restorecon -v /usr/testfile1 |
semanage fcontext -l |
Lists all SELinux file context rules | semanage fcontext -l |
touch /.autorelabel |
Forces SELinux to relabel all files on next reboot | touch /.autorelabel |
Systemd & Services
| Command | Description | Example |
|---|---|---|
systemctl enable --now |
Enables and starts a service | systemctl enable --now httpd |
systemctl status |
Checks the status of a service | systemctl status httpd |
systemctl restart |
Restarts a service | systemctl restart httpd |
systemctl start |
Starts a service | systemctl start vsftpd |
systemctl stop |
Stops a service | systemctl stop httpd |
systemctl disable |
Disables a service from starting on boot | systemctl disable httpd |
systemctl set-default |
Sets the default boot target | systemctl set-default multi-user.target |
systemctl isolate |
Switches to a different target immediately | systemctl isolate multi-user.target |
systemctl daemon-reload |
Reloads systemd configuration | systemctl daemon-reload |
systemctl list-units |
Lists all loaded units | systemctl list-units |
systemctl --user |
Manages user-level (rootless) services | systemctl --user enable --now container-web1.service |
Networking
| Command | Description | Example |
|---|---|---|
nmcli |
NetworkManager command-line tool for network configuration | nmcli connection modify eth0 ipv4.addresses 192.168.0.242/24 ipv4.gateway 192.168.0.1 ipv4.dns 192.168.0.1 ipv4.method manual |
nmcli connection up |
Activates a network connection | nmcli connection up eth0 |
nmcli connection show |
Shows network connections | nmcli connection show |
hostnamectl |
Sets the system hostname persistently | hostnamectl set-hostname rhcsa2.example.com |
hostnamectl set-hostname |
Sets the static hostname | hostnamectl set-hostname rhcsa3.example.com |
hostnamectl set-hostname --transient |
Sets a transient hostname (alias) | hostnamectl set-hostname --transient rhcsa3 |
ping -c2 |
Sends 2 ICMP echo requests to test connectivity | ping -c2 rhcsa4 |
firewall-cmd --permanent --add-service |
Adds a service to firewalld persistently | firewall-cmd --permanent --zone=public --add-service=http |
firewall-cmd --permanent --add-port |
Adds a port to firewalld persistently | firewall-cmd --permanent --zone=public --add-port=8400/udp |
firewall-cmd --permanent --zone=external --add-service |
Adds a service to a specific zone | firewall-cmd --permanent --zone=external --add-service=http |
firewall-cmd --reload |
Reloads firewalld configuration | firewall-cmd --reload |
firewall-cmd --list-all |
Lists all firewalld settings | firewall-cmd --list-all |
firewall-cmd --list-all-zones |
Lists all zones and their settings | firewall-cmd --list-all-zones |
SSH & Remote Access
| Command | Description | Example |
|---|---|---|
ssh |
Connects to a remote system via SSH | ssh user@rhcsa4 |
ssh-keygen |
Generates SSH key pair for password-less access | ssh-keygen -t rsa |
ssh-copy-id |
Copies SSH public key to a remote server | ssh-copy-id user60@rhcsa4 |
scp |
Securely copies files to/from a remote system | scp /etc/sysconfig user@rhcsa6:/var/tmp/remote |
rsync |
Synchronizes files remotely with compression | rsync -avz -e ssh /etc/ user@rhcsa6:/var/tmp/etc/ |
rsync -avz |
Synchronizes with archive mode, verbose, and compression | rsync -avz /etc/ user@rhcsa6:/var/tmp/etc/ |
logout / exit |
Terminates an SSH session | exit |
Package Management (DNF)
| Command | Description | Example |
|---|---|---|
dnf install |
Installs a package | dnf install httpd |
dnf install -y |
Installs a package without prompting | dnf install -y curl |
dnf group install |
Installs a package group | dnf group install "Development Tools" |
dnf module install |
Installs a module stream | dnf module install postgresql:9.6 |
dnf module list |
Lists available module streams | dnf module list |
dnf module enable |
Enables a module stream | dnf module enable container-tools:rhel8 |
dnf module reset |
Resets a module to default state | dnf module reset container-tools |
dnf module info |
Shows module information | dnf module info container-tools |
dnf list |
Lists installed and available packages | dnf list installed |
dnf search |
Searches for packages | dnf search httpd |
dnf provides |
Finds which package provides a file | dnf provides /usr/bin/sealert |
rpm -ql |
Lists all files in an installed package | rpm -ql setup |
subscription-manager register |
Registers the system with RHSM | subscription-manager register --username <user> |
subscription-manager attach |
Attaches a subscription | subscription-manager attach |
subscription-manager refresh |
Refreshes subscription data | subscription-manager refresh |
Storage & File Systems
LVM
| Command | Description | Example |
|---|---|---|
pvcreate |
Creates a physical volume | pvcreate /dev/sdb1 |
vgcreate |
Creates a volume group | vgcreate -s 8M vg1 /dev/sdb1 |
vgcreate -s |
Creates a VG with specified PE size | vgcreate -s 8M myvg /dev/sdb1 |
lvcreate |
Creates a logical volume | lvcreate -L 280M -n lvol1 vgtest |
lvcreate -l |
Creates an LV with specified number of LEs | lvcreate -l 10 -n lv1 vg1 |
lvextend |
Extends a logical volume | lvextend -L +64M /dev/vg1/lv1 |
lvdisplay |
Displays LV information | lvdisplay |
vgdisplay |
Displays VG information | vgdisplay |
pvs |
Shows physical volumes summary | pvs |
vgs |
Shows volume groups summary | vgs |
lvs |
Shows logical volumes summary | lvs |
VDO
| Command | Description | Example |
|---|---|---|
vdo create |
Creates a VDO volume | vdo create --name vdo1 --device /dev/sdb --vdoLogicalSize 16G |
vdo status |
Shows VDO volume status | vdo status --name vdo1 |
Stratis
| Command | Description | Example |
|---|---|---|
stratis pool create |
Creates a Stratis pool | stratis pool create pool1 /dev/sdc |
stratis pool add-data |
Expands a Stratis pool with additional disk | stratis pool add-data pool1 /dev/sdd |
stratis filesystem create |
Creates a Stratis filesystem | stratis filesystem create pool1 str1 |
stratis pool list |
Lists Stratis pools | stratis pool list |
stratis filesystem list |
Lists Stratis filesystems | stratis filesystem list |
File System & Mounting
| Command | Description | Example |
|---|---|---|
mkfs.xfs |
Creates an XFS file system | mkfs.xfs /dev/vg1/lv1 |
mkfs.ext4 |
Creates an Ext4 file system | mkfs.ext4 /dev/sdb2 |
mkfs.vfat |
Creates a FAT file system | mkfs.vfat -n mylabel /dev/sdb1 |
mkswap |
Initializes a swap partition | mkswap /dev/sdb3 |
swapon |
Activates a swap partition | swapon /dev/sdb3 |
swapon --show |
Shows active swap devices | swapon --show |
mount |
Mounts a file system | mount /dev/vg1/lv1 /mnt/mnt1 |
mount -o loop |
Mounts an ISO image using loop device | mount -o loop rhel.iso /repo |
umount |
Unmounts a file system | umount /mnt/mnt1 |
blkid |
Shows block device attributes (UUID, label, type) | blkid /dev/sdb1 |
lsblk |
Lists block devices | lsblk |
df -h |
Shows disk usage in human-readable format | df -h |
xfs_growfs |
Grows an XFS file system online | xfs_growfs /mnt/lvfs1 |
resize2fs |
Resizes an Ext4 file system | resize2fs /dev/vg1/lv1 |
e2label |
Sets/gets an Ext4 file system label | e2label /dev/sdb2 stdlabel |
tune2fs -l |
Shows Ext4 file system information | tune2fs -l /dev/sdb2 |
parted / fdisk |
Creates disk partitions | fdisk /dev/sdb |
ls -ld |
Shows directory/file permissions and ownership | ls -ld /shared |
NFS
| Command | Description | Example |
|---|---|---|
systemctl enable --now nfs-server |
Starts and enables the NFS server service | systemctl enable --now nfs-server |
exportfs -rv |
Reloads NFS exports | exportfs -rv |
showmount -e |
Shows NFS exports on a server | showmount -e rhcsa3 |
systemctl enable --now autofs |
Starts and enables the autofs service | systemctl enable --now autofs |
User & Group Management
| Command | Description | Example |
|---|---|---|
useradd |
Creates a new user account | useradd user10 |
useradd -u |
Creates a user with a specific UID | useradd -u 2929 user40 |
useradd -c |
Creates a user with a comment | useradd -c "I am user70" -u 7000 user70 |
useradd -s |
Creates a user with a specific shell | useradd -s /sbin/nologin user50 |
useradd -s /usr/bin/passwd |
Creates a user who can only change password | useradd -s /usr/bin/passwd bob |
useradd -d |
Creates a user with a custom home directory | useradd -d /home/users/linda linda |
usermod |
Modifies an existing user account | usermod -aG group10 user20 |
usermod -L |
Locks a user account | usermod -L user70 |
usermod -U |
Unlocks a user account | usermod -U user70 |
usermod -e |
Sets account expiration date | usermod -e 2021-12-31 user10 |
usermod -f |
Sets maximum inactivity period (days) | usermod -f 30 user70 |
groupadd |
Creates a new group | groupadd group10 |
groupadd -g |
Creates a group with a specific GID | groupadd -g 3000 group30 |
passwd |
Sets/changes a user’s password | passwd user10 |
chage |
Manages password aging | chage -M 90 user10 |
id |
Shows user/group IDs | id user10 |
su - |
Switches to another user | su - user10 |
sudo |
Executes a command as another user | sudo dnf install httpd |
loginctl enable-linger |
Enables lingering for a user | loginctl enable-linger student |
File Permissions & ACLs
| Command | Description | Example |
|---|---|---|
chmod |
Changes file/directory permissions | chmod 770 /shared |
chmod g+s |
Sets the setgid bit on a directory | chmod g+s /sdata |
chmod o+t |
Sets the sticky bit on a directory | chmod o+t /var/dir1 |
chown |
Changes file/directory ownership | chown root:group10 /mnt/mnt1 |
chgrp |
Changes group ownership | chgrp group10 /mnt/mnt1 |
setfacl -m |
Sets an access ACL | setfacl -m u:user10:rwx /var/tmp/dir1 |
setfacl -d -m |
Sets a default ACL | setfacl -d -m u:user10:rwx /var/tmp/dir1 |
setfacl -m u:user10:rw |
Sets read/write ACL for a user | setfacl -m u:user10:rw /var/tmp/testfile1 |
getfacl |
Shows ACLs on a file/directory | getfacl /var/tmp/dir1 |
File Operations & Archives
| Command | Description | Example |
|---|---|---|
tar -cjf |
Creates a bzip2-compressed archive | tar -cjf /var/tmp/usr.tar.bz2 /usr/lib |
tar -czf |
Creates a gzip-compressed archive | tar -czf /var/tmp/etc.tar.gz /etc |
tar -xjf |
Extracts a bzip2-compressed archive | tar -xjf /var/tmp/usr.tar.bz2 |
tar -xzf |
Extracts a gzip-compressed archive | tar -xzf /var/tmp/etc.tar.gz |
ln |
Creates a hard link | ln /var/tmp/lnfile1 /var/tmp/lnfile2 |
ln -s |
Creates a symbolic (soft) link | ln -s /var/tmp/lnfile1 /boot/file1 |
stat |
Shows file statistics (inode, size, timestamps) | stat /var/tmp/lnfile1 |
find |
Searches for files by various criteria | find / -name "core" -mtime -30 |
find -user |
Finds files owned by a specific user | find / -user edwin |
find -exec |
Executes a command on found files | find /var -name "core" -exec cp {} /var/tmp/coredir1 \; |
find -mtime |
Finds files modified within N days | find / -mtime -30 > /var/tmp/modfiles.txt |
cp |
Copies files/directories | cp /etc/sysconfig user@rhcsa6:/var/tmp/remote |
mkdir -p |
Creates directories recursively | mkdir -p /dir1/dir2/dir3/dir4 |
grep -i |
Case-insensitive search | grep -i "^essential" /usr/share/dict/linux.words |
grep -v |
Inverts match (excludes matching lines) | grep -v "^$" /var/tmp/pattern.txt |
man -k |
Searches manual pages by keyword | man -k password |
updatedb |
Updates the locate database | updatedb |
locate |
Locates files using the locate database | locate sealert |
Scheduling & Automation
| Command | Description | Example |
|---|---|---|
crontab -e |
Edits a user’s crontab | crontab -e |
crontab -l |
Lists a user’s crontab | crontab -l |
cron expression |
Schedules recurring tasks | 20 1 * * 1 find /var -name "core" -exec cp {} /var/tmp/coredir1 \; |
at |
Schedules a one-time task | echo "touch /tmp/file" | at 2:00am |
atd |
The at daemon service | systemctl enable --now atd |
Logging & Journal
| Command | Description | Example |
|---|---|---|
journalctl |
Views systemd journal logs | journalctl |
journalctl -xb |
Views logs for the current boot | journalctl -xb |
logger |
Sends custom messages to the system log | logger "This is RHCSA sample exam on $(date) by $LOGNAME" |
grep |
Searches log output | grep "RHCSA" /var/log/messages |
System Tuning
| Command | Description | Example |
|---|---|---|
tuned-adm profile |
Applies a tuning profile | tuned-adm profile powersave |
tuned-adm active |
Shows the currently active tuning profile | tuned-adm active |
tuned-adm recommend |
Shows the recommended tuning profile | tuned-adm recommend |
Time Synchronization (Chrony)
| Command | Description | Example |
|---|---|---|
chronyc sources |
Shows NTP sources | chronyc sources |
chronyc tracking |
Shows time synchronization status | chronyc tracking |
systemctl enable --now chronyd |
Starts and enables the chronyd service | systemctl enable --now chronyd |
Shell & Environment
| Command | Description | Example |
|---|---|---|
export |
Sets an environment variable | export ENV1=book1 |
echo |
Prints text or variable values | echo $ENV1 |
echo > |
Writes text to a file | echo "Welcome" > /var/www/html/index.html |
cat |
Displays file contents | cat /etc/redhat-release |
uname -r |
Shows the kernel version | uname -r |
whoami |
Shows the current user | whoami |
hostname |
Shows the system hostname | hostname |
pwd |
Shows the current working directory | pwd |
ls |
Lists directory contents | ls -la /var/www/html |
date |
Shows the current date and time | date |
df |
Shows disk space usage | df -h |
os-release |
Shows OS release information | cat /etc/os-release |
grep |
Searches text using patterns | grep "hosts" /etc/setup.pkg |
tee |
Writes to a file and displays output | podman generate systemd | tee /etc/systemd/system/container.service |
less |
Views file contents page by page | podman inspect ubi9 | less |
vi / vim |
Text editor for modifying files | vi /etc/fstab |
:%s/old/new/g |
Vi command to replace all occurrences | :%s/account/sales/g |
Repository & ISO Mounting
| Command | Description | Example |
|---|---|---|
mount -o loop |
Mounts an ISO image | mount -o loop rhel-9.iso /repo |
dnf repolist |
Lists configured repositories | dnf repolist |
dnf config-manager |
Manages repository configuration | dnf config-manager --add-repo=file:///repo |
Kernel Management
| Command | Description | Example |
|---|---|---|
uname -r |
Shows the current kernel version | uname -r |
dnf install kernel |
Installs the latest kernel | dnf install kernel |
grub2-mkconfig -o /boot/grub2/grub.cfg |
Regenerates GRUB configuration | grub2-mkconfig -o /boot/grub2/grub.cfg |
Default User Settings
| Command | Description | Example |
|---|---|---|
useradd -D |
Shows or sets default useradd settings | useradd -D |
useradd -D -b |
Sets the default base directory for new users | useradd -D -b /home |
useradd -D -g |
Sets the default group for new users | useradd -D -g users |
useradd -D -s |
Sets the default shell for new users | useradd -D -s /bin/bash |
useradd -D -u |
Sets the first UID for new users | useradd -D -u 2000 |
useradd -D -e |
Sets the default password validity | chage -M 90 |
useradd -D -f |
Sets the default inactivity period | useradd -D -f 30 |
useradd -D -s /sbin/nologin |
Sets default shell to non-interactive | useradd -D -s /sbin/nologin |
Default User Skeleton
| File/Directory | Description |
|---|---|
/etc/default/useradd |
Default settings for new users |
/etc/login.defs |
System-wide login defaults (UID range, password aging) |
/etc/skel/ |
Skeleton directory; files here are copied to new user home directories |
/etc/skel/NEWFILE |
A file placed here will be copied to each new user’s home directory |
Practice Exam-Specific Commands
Commands from Sample Exam 1
| Command | Description | Example |
|---|---|---|
grep -i "^essential" /usr/share/dict/linux.words > /var/tmp/pattern.txt |
Case-insensitive search for lines starting with “essential” | grep -i "^essential" /usr/share/dict/linux.words | grep -v "^$" > /var/tmp/pattern.txt |
PS1 |
Sets the command prompt | PS1='\h \u \w \$ ' |
~/.bashrc |
Per-user initialization file for prompt permanence | echo "PS1='\h \u \w \$ '" >> ~/.bashrc |
chage -E |
Sets account expiration date | chage -E 2021-12-31 user10 |
visudo |
Edits the sudoers file | visudo |
user20 ALL=(ALL) NOPASSWD: ALL |
Allows user20 to use sudo without password | Add to /etc/sudoers |
man -k password > /var/tmp/man.out |
Searches manual pages and redirects output | man -k password > /var/tmp/man.out |
logger |
Logs custom messages | logger "This is RHCSA sample exam on $(date) by $LOGNAME" |
grep "RHCSA" /var/log/messages |
Confirms log entry | grep "RHCSA" /var/log/messages |
at.allow / at.deny |
Controls user access to the atd service | Add/remove users from /etc/at.allow and /etc/at.deny |
Commands from Sample Exam 2
| Command | Description | Example |
|---|---|---|
nmcli connection modify |
Configures network via nmcli | nmcli connection modify eth0 ipv4.addresses 192.168.0.242/24 ipv4.gateway 192.168.0.1 ipv4.dns 192.168.0.1 ipv4.method manual |
chage -I |
Sets maximum inactivity period | chage -I 30 user70 |
useradd -s /sbin/nologin |
Creates a user with non-interactive shell | useradd -s /sbin/nologin user50 |
mkfs.ext4 -L |
Creates Ext4 with a label | mkfs.ext4 -L stdlabel /dev/sdb2 |
mount -L |
Mounts by label | mount -L stdlabel /mnt/stdfs1 |
xfs_growfs |
Grows XFS file system online | xfs_growfs /mnt/lvfs1 |
lvextend -L +64M |
Extends LV by 64MB | lvextend -L +64M /dev/vg1/lv1 |
tuned-adm recommend |
Shows recommended tuning profile | tuned-adm recommend |
tuned-adm profile |
Applies a tuning profile | tuned-adm profile powersave |
chronyc |
Chrony time sync utility | chronyc sources |
dnf groupinfo |
Shows package group information | dnf groupinfo "Development Tools" > /var/tmp/systemtools.out |
passwd -S |
Shows password status (locked/unlocked) | passwd -S user70 |
grep "L" /etc/shadow |
Checks if account is locked | grep "user70.*L" /etc/shadow > /var/tmp/user70.lock |
grubby |
Modifies bootloader configuration | grubby --update-kernel=ALL --args="..." |
Commands from Sample Exam 3
| Command | Description | Example |
|---|---|---|
semanage port -a -t http_port_t -p tcp 8300 |
Adds HTTP port to SELinux policy | semanage port -a -t http_port_t -p tcp 8300 |
vdo create |
Creates a VDO volume | vdo create --name vdo1 --device /dev/sdb --vdoLogicalSize 16G |
systemctl enable --now nfs-server |
Starts NFS server | systemctl enable --now nfs-server |
systemctl enable --now autofs |
Starts autofs | systemctl enable --now autofs |
stratis pool create |
Creates a Stratis pool | stratis pool create pool1 /dev/sdc |
stratis filesystem create |
Creates a Stratis filesystem | stratis filesystem create pool1 str1 |
stratis pool add-data |
Expands a Stratis pool | stratis pool add-data pool1 /dev/sdd |
chmod g+s |
Sets setgid bit | chmod g+s /sdata |
chmod 1777 |
Sets sticky bit with full permissions | chmod 1777 /var/dir1 |
ln |
Creates a hard link | ln /var/tmp/lnfile1 /var/tmp/lnfile2 |
ln -s |
Creates a soft link | ln -s /var/tmp/lnfile1 /boot/file1 |
dnf module install postgresql:9.6 |
Installs a specific module stream | dnf module install postgresql:9.6 |
firewall-cmd --permanent --zone=external --add-service=http |
Adds HTTP to external zone | firewall-cmd --permanent --zone=external --add-service=http |
firewall-cmd --reload |
Reloads firewall | firewall-cmd --reload |
chcon -t shadow_t |
Sets SELinux type | chcon -t shadow_t /usr/testfile1 |
semanage fcontext -a -t shadow_t '/usr/testfile1' |
Sets persistent SELinux context | semanage fcontext -a -t shadow_t '/usr/testfile1' |
restorecon -v |
Restores SELinux context | restorecon -v /usr/testfile1 |
ssh-keygen |
Generates SSH keys | ssh-keygen -t rsa |
ssh-copy-id |
Copies SSH key to remote host | ssh-copy-id user60@rhcsa4 |
stat |
Shows file statistics | stat /usr/bin/ac* |
podman port |
Validates port mapping | podman port container-name |
podman exec -it |
Verifies environment variables | podman exec -it container-name env |
Commands from Sample Exam 4
| Command | Description | Example |
|---|---|---|
semanage port -a -t http_port_t -p udp 8400 |
Adds UDP port to SELinux policy | semanage port -a -t http_port_t -p udp 8400 |
scp -r |
Securely copies a directory | scp -r /etc/sysconfig user@rhcsa6:/var/tmp/remote |
rsync -avz -e ssh |
Synchronizes with compression | rsync -avz -e ssh /etc/ user@rhcsa6:/var/tmp/etc/ 2>&1 > /var/tmp/etc.transfer |
semanage boolean -m --on nfs_export_all_rw |
Enables SELinux boolean persistently | semanage boolean -m --on nfs_export_all_rw |
ln |
Creates hard links | ln /var/tmp/lnfile1 /var/tmp/hard1 |
stat |
Shows inode number | stat /var/tmp/lnfile1 |
rpm -ql setup |
Lists files in a package | rpm -ql setup |
grep "hosts" |
Filters output for “hosts” | rpm -ql setup | grep "hosts" > /var/tmp/setup.pkg |
uname -r |
Checks kernel version | uname -r |
subscription-manager register |
Registers with RHSM | subscription-manager register |
dnf install kernel |
Installs latest kernel | dnf install kernel |
journalctl |
Configures journald | Create /var/log/journal directory |
podman run -d --name |
Launches named root container | podman run -d --name mycontainer -p 443:443 ubi7 |
podman generate systemd --new --name |
Generates systemd unit for container | podman generate systemd --new --name mycontainer --files |
podman run -e KERN=$(uname -r) |
Passes command substitution as env var | podman run -e KERN=$(uname -r) -e SHELL ubi8 |
Commands from Practice Exam A
| Command | Description | Example |
|---|---|---|
useradd |
Creates a user | useradd student |
passwd |
Sets a password | passwd student |
mount -o loop |
Mounts ISO persistently | mount -o loop /path/to/iso /repo |
useradd -D -u 2000 |
Sets first UID for new users | useradd -D -u 2000 |
chage -M 90 |
Sets default password validity to 90 days | chage -M 90 |
usermod -aG |
Adds user to a secondary group | usermod -aG livingopensource edwin |
useradd -u 1234 -s /sbin/nologin |
Creates user with specific UID and no shell | useradd -u 1234 -s /sbin/nologin santos |
chmod 2770 |
Sets setgid and full group access | chmod 2770 /groups/livingopensource |
chown root:livingopensource |
Sets ownership and group | chown root:livingopensource /groups/livingopensource |
vgcreate -s 8M |
Creates VG with 8MiB PE size | vgcreate -s 8M myvg /dev/sdb1 |
lvcreate -L 500M -n mydata myvg |
Creates 500MiB LV | lvcreate -L 500M -n mydata myvg |
mkfs.ext4 |
Formats with Ext4 | mkfs.ext4 /dev/myvg/mydata |
mount |
Mounts persistently | mount /dev/myvg/mydata /mydata |
find -user -exec cp |
Finds and copies files | find / -user edwin -exec cp {} /root/edwinfiles/ \; |
crontab -e |
Schedules daily Mon-Fri 2am | 0 2 * * 1-5 touch /etc/motd |
stratis pool create |
Creates Stratis pool | stratis pool create mypool /dev/sdc |
stratis filesystem create |
Creates Stratis filesystem | stratis filesystem create mypool myfs |
useradd -s /usr/bin/passwd |
User can only change password | useradd -s /usr/bin/passwd bob |
dnf install vsftpd |
Installs FTP server | dnf install vsftpd |
systemctl enable --now vsftpd |
Starts and enables vsftpd | systemctl enable --now vsftpd |
podman run -d --name |
Runs HTTP container | podman run -d --name httpd -v /httproot:/var/www/html:Z httpd |
podman generate systemd --new --files |
Generates systemd unit | podman generate systemd --new --files --name httpd |
systemctl enable --now |
Enables container service | systemctl enable --now container-httpd.service |
mkdir -p |
Creates NFS export directories | mkdir -p /users/linda /users/anna |
systemctl enable --now nfs-server |
Starts NFS server | systemctl enable --now nfs-server |
systemctl enable --now autofs |
Starts autofs | systemctl enable --now autofs |
useradd -d |
Creates user with custom home | useradd -d /home/users/linda linda |
Commands from Practice Exam B
| Command | Description | Example |
|---|---|---|
fdisk / parted |
Creates a partition | fdisk /dev/sdb |
mkfs.vfat -n mylabel |
Formats with vfat and label | mkfs.vfat -n mylabel /dev/sdb1 |
mount -L mylabel /mydata |
Mounts by label | mount -L mylabel /mydata |
cp /etc/skel/NEWFILE |
Copies skeleton file for new users | Place NEWFILE in /etc/skel/ |
chmod 1770 |
Sets sticky bit with group access | chmod 1770 /groups/livingopensource |
mkswap |
Initializes swap | mkswap /dev/sdb2 |
swapon |
Activates swap | swapon /dev/sdb2 |
lvextend -L +1G |
Extends LV by 1GiB | lvextend -L +1G /dev/mapper/rhel-root |
xfs_growfs / |
Grows root XFS filesystem | xfs_growfs / |
find -user -exec cp |
Finds and copies user files | find / -user linda -exec cp {} /tmp/lindafiles/ \; |
useradd -u 2008 |
Creates user with custom UID | useradd -u 2008 vicky |
dnf install httpd |
Installs web server | dnf install httpd |
systemctl enable --now httpd |
Starts and enables web server | systemctl enable --now httpd |
podman run -d --name |
Runs rootless MySQL container | podman run -d --name mysql -e MYSQL_ROOT_PASSWORD=password -v /home/student/mysql:/var/lib/mysql:Z docker.io/library/mysql:latest |
podman generate systemd --new --files --name mysql |
Generates systemd unit for rootless container | podman generate systemd --new --files --name mysql |
systemctl --user enable --now |
Enables rootless container service | systemctl --user enable --now container-mysql.service |
loginctl enable-linger |
Enables linger for rootless autostart | loginctl enable-linger linda |
Configuration Files Reference
| File | Purpose |
|---|---|
/etc/fstab |
Persistent file system mount definitions |
/etc/hosts |
Static hostname-to-IP mappings |
/etc/hostname |
System hostname |
/etc/default/grub |
GRUB bootloader configuration |
/boot/grub2/grub.cfg |
GRUB configuration (generated) |
/etc/dracut.conf |
Dracut initramfs configuration (deprecated) |
/etc/dracut.conf.d/ |
Dracut configuration drop-in directory |
/etc/containers/registries.conf |
Container registry configuration |
/etc/httpd/conf/httpd.conf |
Apache main configuration |
/etc/httpd/conf.d/ |
Apache drop-in configuration directory |
/etc/sudoers |
Sudo access control |
/etc/at.allow |
Users allowed to use atd |
/etc/at.deny |
Users denied from using atd |
/etc/login.defs |
System-wide login defaults |
/etc/default/useradd |
Default useradd settings |
/etc/skel/ |
Skeleton directory for new user homes |
/etc/exports |
NFS export definitions |
/etc/auto.master |
Autofs master configuration |
/etc/auto.direct |
Autofs direct map |
/etc/auto.indirect |
Autofs indirect map |
/etc/chrony.conf |
Chrony time synchronization configuration |
/etc/journald.conf |
Journal configuration |
/var/log/journal/ |
Persistent journal storage |
/etc/systemd/system/ |
System-level systemd unit files |
~/.config/systemd/user/ |
User-level systemd unit files |
/etc/sysctl.conf |
Kernel parameter tuning |
/root/anaconda-ks.cfg |
Anaconda kickstart configuration |
/root/install.log |
Installation package log |
/var/log/anaconda/ |
Anaconda installation logs |
/etc/yum.repos.d/ |
Repository configuration files |