Domain 3IP ConnectivityCORE

IPv4 and IPv6 Static Routing

Configuring and verifying static routes for IPv4 and IPv6, including default routes and interpreting the routing table.

Domain: Domain 3: IP Connectivity•Updated: 2026-08-26
#Static Routing#IPv4 Routes#IPv6 Routes#Default Route#Routing Table

Routing Fundamentals & Static Routing

Routing Basics

  • Concept: Routing is the process routers use to determine the path that IP packets should take over a network to reach their destination.
  • Routing Table: A set of instructions stored on the router. Each route tells the router: “To send a packet to destination X, forward it to next-hop Y” (or directly to the destination if connected).
  • Routing Methods:
    • Dynamic Routing: Routers use protocols (e.g., OSPF) to automatically share routing information and build tables.
    • Static Routing: A network administrator manually configures routes.

Connected and Local Routes

When an IP address is configured on a router interface and enabled with no shutdown, two routes are automatically added to the routing table per interface.

  • Connected Route (Code: C): A route to the entire network the interface is connected to.
    • Example: Interface IP 192.168.1.1/24 generates a connected route to 192.168.1.0/24.
  • Local Route (Code: L): A route to the exact IP address configured on the interface, using a /32 subnet mask.
    • Example: Interface IP 192.168.1.1/24 generates a local route to 192.168.1.1/32.
    • Purpose: Tells the router, “If a packet is destined for this exact IP, receive it for yourself; do not forward it.”
Router(config)# interface gigabitethernet0/2
Router(config-if)# ip address 192.168.1.1 255.255.255.0
Router(config-if)# no shutdown
Router(config-if)# exit
Router# show ip interface brief
Router# show ip route

Things to note: In the show ip route output, you may see lines like 192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks. These are not routes; they are informational headers indicating that the routing table contains multiple subnets and masks within that major network.

Route Selection Rules

When a router receives a packet, it evaluates the routing table to make a forwarding decision based on two strict rules:

  1. Match: The packet’s destination IP address must fall within the network range specified by the route.
  2. Longest Prefix Match (Most Specific Match): If multiple routes match the destination, the router selects the route with the longest subnet mask (highest prefix length).
    • Example: A packet destined for 192.168.1.1 matches both 192.168.1.0/24 and 192.168.1.1/32. The /32 route is more specific (longest prefix), so the router selects it and processes the packet locally.

Things to note: If no route matches the destination IP, the router will drop the packet. Unlike switches, routers never flood unknown unicast packets.

Router vs. Switch Forwarding Behavior

Feature Switches (Layer 2) Routers (Layer 3)
Forwarding Table MAC Address Table Routing Table
Match Type Exact MAC address match Longest Prefix Match (IP)
Unknown Destination Floods the frame out all ports (except ingress) Drops the packet

Static Routing Configuration

Static routes are manually configured to reach remote networks not directly connected to the router.

Command Syntax

Router(config)# ip route <destination_network> <subnet_mask> <next_hop_ip | exit_interface | both>
  • Next-Hop IP: The IP address of the adjacent router’s interface (Recommended).
  • Exit Interface: The local interface the packet should be sent out of.
  • Both: Specifies both the exit interface and next-hop IP.

Configuration Example (Path: PC1 -> R1 -> R3 -> R4 -> PC4)

! On R1: Route to PC4's network (192.168.4.0/24) via R3
R1(config)# ip route 192.168.4.0 255.255.255.0 192.168.13.3

! On R3: Route to PC1's network (192.168.1.0/24) via R1
R3(config)# ip route 192.168.1.0 255.255.255.0 192.168.13.1
! On R3: Route to PC4's network (192.168.4.0/24) via R4
R3(config)# ip route 192.168.4.0 255.255.255.0 192.168.34.4

! On R4: Route to PC1's network (192.168.1.0/24) via R3
R4(config)# ip route 192.168.1.0 255.255.255.0 192.168.34.3

Next-Hop vs. Exit Interface Behavior

Configuration Method Routing Table Display Underlying Mechanism
Next-Hop IP only Shows next-hop IP address Standard recursive lookup.
Exit Interface only Shows as is directly connected Relies on Proxy ARP to resolve the next-hop MAC address. (Note: Proxy ARP is beyond CCNA scope, but the display behavior is testable).
Both Shows both interface and next-hop Combines benefits; avoids recursive lookup delays and Proxy ARP reliance.

Things to note: You cannot use prefix length notation (e.g., /24) in the ip route command. You must use the dotted-decimal subnet mask (e.g., 255.255.255.0).

Default Routing

  • Concept: A default route is the “least specific” route possible (0.0.0.0 0.0.0.0). It matches any destination IP address.
  • Purpose: Acts as a catch-all for traffic destined to networks not explicitly listed in the routing table (commonly used to point toward the Internet).
  • Terminology: Also known as the Gateway of Last Resort.
! Configure default route pointing to an ISP router
Router(config)# ip route 0.0.0.0 0.0.0.0 203.0.113.2

Things to note: In the show ip route output, a default route is marked with an asterisk (S*), indicating it is a candidate default. The output will also state: Gateway of last resort is 203.0.113.2 to network 0.0.0.0.

Layer 2 vs. Layer 3 Packet Forwarding

When a packet travels across multiple routers, Layer 3 and Layer 2 headers behave differently:

  • Layer 3 (IP Header): Source and Destination IP addresses never change from the original sender to the final receiver.
  • Layer 2 (Ethernet Header): Source and Destination MAC addresses change at every hop.
    1. Sender encapsulates packet with Default Gateway’s MAC as destination.
    2. Router de-encapsulates L2, checks L3 routing table, and re-encapsulates with the next-hop router’s MAC as the new destination.
    3. This repeats until the final router encapsulates the packet with the end host’s MAC address.
sequenceDiagram
    participant PC1
    participant R1
    participant R3
    participant R4
    participant PC4
    
    PC1->>R1: L2 Dest: R1 MAC | L3 Dest: PC4 IP
    R1->>R3: L2 Dest: R3 MAC | L3 Dest: PC4 IP
    R3->>R4: L2 Dest: R4 MAC | L3 Dest: PC4 IP
    R4->>PC4: L2 Dest: PC4 MAC | L3 Dest: PC4 IP

Command Summary

! View interface IP assignments and status
Router# show ip interface brief

! View the routing table (includes Codes legend, C=Connected, L=Local, S=Static)
Router# show ip route

! Configure a static route using Next-Hop IP (Recommended)
Router(config)# ip route <destination_network> <subnet_mask> <next_hop_IP>

! Configure a static route using Exit Interface only
Router(config)# ip route <destination_network> <subnet_mask> <exit_interface>

! Configure a static route using BOTH Exit Interface and Next-Hop IP
Router(config)# ip route <destination_network> <subnet_mask> <exit_interface> <next_hop_IP>

! Configure a default route (Gateway of Last Resort)
Router(config)# ip route 0.0.0.0 0.0.0.0 <next_hop_IP>

Common Misconceptions to Avoid:

  1. Routers flood unknown traffic: False. Routers drop packets if no matching route exists. Only switches flood unknown unicast frames.
  2. /32 means a network route: False. A /32 route is a host route (Local route), specifying exactly one IP address.
  3. Static routes can use /24 syntax: False. The ip route command strictly requires dotted-decimal subnet masks (e.g., 255.255.255.0), not CIDR slash notation.
  4. Two-way reachability: Configuring a route on R1 to reach R4 does not guarantee R4 can reply. You must configure return routes on all intermediate routers (R4 -> R3 -> R1) for communication (like ICMP ping) to succeed.